Skip to main content ↑ ↓
Topic: long tube headers (Read 2445 times) previous topic - next topic

long tube headers

anyone know what long tube headers will fit 83 thunderbird with 351w must be 1 5/8 primary at least with 3 in collector

long tube headers

Reply #1 –
BBK or Hooker, get them for a fox body mustang. You'll have to run a floor shifter if you're using a auto. You'll be fine if you're using a manual.
88 Cougar LS 5.0 .030 over, ported E7s with GT40 valves & trickflow springs, Proform roller rockers, HO cam, removed air silencer, K&N filter, smog pump delete, 2.25" dual flowmasters, Pacestter H-pipe & headers, HO computer, 65mm TB, Explorer intake, 19# injecters, 3.45s, rebuilt posi, and TCI shift kit.

long tube headers

Reply #2 –
Why 1 5/8 when you can have a 1 3/4 or even 1 7/8 if you ever go boosted or big heads and cam a 408 loves to breathe. I have a 351 with bbk's 1 5/8 shoties?
[SIGPIC][/SIGPIC]:ford:87 Turbo Coupe through the floor sub frame connectors, 5.8 swap Ford racing heads Harland sharp 1.6 rockers BBK shorty swap headers 2 1/2 BBk X pipe magnaflow ler's. Megasquirt 2 with 36lbs injectors on hurricane intake with 4150 throttle body.Tremec TKO 600 Quicktime blowsheild spec stage 3 clutch. 3.73 gears and still not done

long tube headers

Reply #3 –
He said at least 1 5/8th primary.
Quote from: jcassity
I honestly dont think you could exceed the cost of a new car buy installing new *stock* parts everywhere in your coug our tbird. Its just plain impossible. You could revamp the entire drivetrain/engine/suspenstion and still come out ahead.
Hooligans! 
1988 Crown Vic wagon. 120K California car. Wifes grocery getter. (junked)
1987 Ford Thunderbird LX. 5.0. s.o., sn-95 t-5 and an f-150 clutch. Driven daily and going strong.
1986 cougar.
lilsammywasapunkrocker@yahoo.com

long tube headers

Reply #4 –
I'm pretty sure they don't make a 351 swap LT header any smaller than 1 5/8"
[SIGPIC][/SIGPIC]:ford:87 Turbo Coupe through the floor sub frame connectors, 5.8 swap Ford racing heads Harland sharp 1.6 rockers BBK shorty swap headers 2 1/2 BBk X pipe magnaflow ler's. Megasquirt 2 with 36lbs injectors on hurricane intake with 4150 throttle body.Tremec TKO 600 Quicktime blowsheild spec stage 3 clutch. 3.73 gears and still not done

long tube headers

Reply #5 –
If I ever did a 351 swap, I'd us Hooker 1 3/4".
88 Cougar LS 5.0 .030 over, ported E7s with GT40 valves & trickflow springs, Proform roller rockers, HO cam, removed air silencer, K&N filter, smog pump delete, 2.25" dual flowmasters, Pacestter H-pipe & headers, HO computer, 65mm TB, Explorer intake, 19# injecters, 3.45s, rebuilt posi, and TCI shift kit.

long tube headers

Reply #6 –
reason for 1 5/8 is the small trick flow heads 170 I'm using its a coast high 408 pro street with 10.5/1 compression so I don't think I would need any bigger for this year. hopefully 100 or 150 shot of nitrous will make up for it at the track

long tube headers

Reply #7 –
small heads on my coast high 408 170 trick flow

long tube headers

Reply #8 –
I was looking at a rpm air gap intake and to match the in flow I was told I need 1 7/8 primaries ? and I would love a set of stainless steel once and done.
[SIGPIC][/SIGPIC]:ford:87 Turbo Coupe through the floor sub frame connectors, 5.8 swap Ford racing heads Harland sharp 1.6 rockers BBK shorty swap headers 2 1/2 BBk X pipe magnaflow ler's. Megasquirt 2 with 36lbs injectors on hurricane intake with 4150 throttle body.Tremec TKO 600 Quicktime blowsheild spec stage 3 clutch. 3.73 gears and still not done

long tube headers

Reply #9 –
Quote from: 83thunderbird;357064
reason for 1 5/8 is the small trick flow heads 170 I'm using its a coast high 408 pro street with 10.5/1 compression so I don't think I would need any bigger for this year. hopefully 100 or 150 shot of nitrous will make up for it at the track
.....if you stick with the 1 5/8"....you're leaving 15-25HP on the table with that CID.  :beatyoass:
84 COUGAR/90 HO, 1.7RRs, performer RPM,700DP, equal length shorties, stainless EXH ,T-5,Hurst pro-billet, KC clutch, 8.8/ 4.10s, line-lok, bla ,bla, bla.
71 COMET/289,351w heads, 12.5 TRWs, 750DP, Liberty TL, 9"/6.00s, 11.9x @112 , bla,bla,bla.

Never shoot your mouth off, unless your brain is loaded! ....I may get older, but I'll never grow up!....If you're not laughing, you're not living!  :laughing:
 

long tube headers

Reply #10 –
even with a small 170 cc trick flow head

long tube headers

Reply #11 –
Quote from: thewestie;357042
I'm pretty sure they don't make a 351 swap LT header any smaller than 1 5/8"

I didn't know they made ANY a/m headers less than 1 5/8"... heck even the 3.8 headers are all 1 5/8"
--Steve
[thread=28690]1988 Cougar V6[/thread]
2012 F-150 3.7L
2011 Mustang 3.7L

long tube headers

Reply #12 –
Headmen makes 1.5" headers four our cars.
88 Cougar LS 5.0 .030 over, ported E7s with GT40 valves & trickflow springs, Proform roller rockers, HO cam, removed air silencer, K&N filter, smog pump delete, 2.25" dual flowmasters, Pacestter H-pipe & headers, HO computer, 65mm TB, Explorer intake, 19# injecters, 3.45s, rebuilt posi, and TCI shift kit.

long tube headers

Reply #13 –
wow. I was unaware.
--Steve
[thread=28690]1988 Cougar V6[/thread]
2012 F-150 3.7L
2011 Mustang 3.7L

long tube headers

Reply #14 –
I had the 1-1/2" Headmans when I converted my car over to a T-5 in '93.  With the stock CFI on the 5.0 and 2-1/4" dual exhaust is was a pretty good setup for the stock motor.  Getting the bolts in and out of the header  was a breeze and the plug wires had plenty of room too.

Darren

83 351W TKO'd T-Bird on the bottle


93 331 Mustang Coupe - 368 rwhp