Skip to main content ↑ ↓
Topic: Project Evolution *** Project Complete **** Wednesday July 9, 2014 (Read 1160947 times) previous topic - next topic

Project Evolution *** Project Complete **** Wednesday July 9, 2014

Reply #1650 –
Quote from: HAVI;299072
Is that foil faced hard insulation in the ceiling?  How was it laying it out?  Did you cut it out around each rafter?

BTW, sorry about your grandfather....I lost mine recently, too.


Thanks Scott,

No, I put plywood on top of the ceiling joists for storage, but before I did that, I put a foil radiant barrier on the underside of the plywood.
I have to finish the ends still, and there will be an insulated suspended ceiling about an inch below the joists to cover everything.
[SIGPIC][/SIGPIC]
***** Project "EVOLUTION" 1987 Cougar LS  & 1985 Cougar Convertible *****
[/COLOR]
5.0 HO 306 roller block, machined GT-40P heads, Wiseco dished forged pistons, Eagle forged floating I-beam connecting rods, Lunati pushrods, ARP bolts, Scorpion aluminum 1.6 rockers, Comp Cams Magnum 266HR, Explorer intake, 65mm TB, MAF Conversion, 19# injectors, Ford Racing stainless P-headers, 2-1/2" cat-less exhaust w/ Flowtech Afterburner lers , SC AOD with 2800 BDR torque converter, 3.73 T-Lok rear, CHE rear control arms, full 2-1/2" frame w/1" jacking rails & seat supports, Rear disk brakes, Turbine wheels, All original interior w/ floor shift upgrade .......
Pretty much every panel on my 87 is new, rebuilt, or re constructed. :D
Join us on Facebook
http://www.facebook.com/home.php?sk=group_137541156293768&ap=1

Project Evolution *** Project Complete **** Wednesday July 9, 2014

Reply #1651 –
Looking good, is one goin to be a spray booth ? If so I'm taking time off this winter with the cat to visit.
Old Grey Cat to this.88 Cat, 5.0 HO, CW mounts, mass air, CI custom cam, afr165's, Tmoss worked cobra intake, BBK shorty's,off road h pipe, magnaflow ex. T-5,spec stage 2 clutch, 8.8 373 TC trac loc, che ajustables with bullits on the rear. 11" brakes up front. +

Project Evolution *** Project Complete **** Wednesday July 9, 2014

Reply #1652 –
I'm going to make it so I can divide 1 bay with a movable plastic wall and movable wall lighting, and I scored a nice exhaust fan with an exterior motor on a pulley. You may want to visit it. lol
[SIGPIC][/SIGPIC]
***** Project "EVOLUTION" 1987 Cougar LS  & 1985 Cougar Convertible *****
[/COLOR]
5.0 HO 306 roller block, machined GT-40P heads, Wiseco dished forged pistons, Eagle forged floating I-beam connecting rods, Lunati pushrods, ARP bolts, Scorpion aluminum 1.6 rockers, Comp Cams Magnum 266HR, Explorer intake, 65mm TB, MAF Conversion, 19# injectors, Ford Racing stainless P-headers, 2-1/2" cat-less exhaust w/ Flowtech Afterburner lers , SC AOD with 2800 BDR torque converter, 3.73 T-Lok rear, CHE rear control arms, full 2-1/2" frame w/1" jacking rails & seat supports, Rear disk brakes, Turbine wheels, All original interior w/ floor shift upgrade .......
Pretty much every panel on my 87 is new, rebuilt, or re constructed. :D
Join us on Facebook
http://www.facebook.com/home.php?sk=group_137541156293768&ap=1

Project Evolution *** Project Complete **** Wednesday July 9, 2014

Reply #1653 –
hell i may just visit it next weekend if you are not buisy jerry.
2001 Buick Regal LS (DD):hick:

Got that fox rash again!

-Resident smartass! :ies:

- Don't listen to the naysayers. For every person who actually helps with your project there will be 10 who will discourage you all the while thinking that they are helping. 99% of all people have good intentions. That doesn't make them right.- XR7 Dave - SCCOA.Com

Project Evolution *** Project Complete **** Wednesday July 9, 2014

Reply #1654 –
I'll be working on it. gotta get the heat runs in.
Stop by and get your snow tires if your going to your parents for Thanksgiving.
[SIGPIC][/SIGPIC]
***** Project "EVOLUTION" 1987 Cougar LS  & 1985 Cougar Convertible *****
[/COLOR]
5.0 HO 306 roller block, machined GT-40P heads, Wiseco dished forged pistons, Eagle forged floating I-beam connecting rods, Lunati pushrods, ARP bolts, Scorpion aluminum 1.6 rockers, Comp Cams Magnum 266HR, Explorer intake, 65mm TB, MAF Conversion, 19# injectors, Ford Racing stainless P-headers, 2-1/2" cat-less exhaust w/ Flowtech Afterburner lers , SC AOD with 2800 BDR torque converter, 3.73 T-Lok rear, CHE rear control arms, full 2-1/2" frame w/1" jacking rails & seat supports, Rear disk brakes, Turbine wheels, All original interior w/ floor shift upgrade .......
Pretty much every panel on my 87 is new, rebuilt, or re constructed. :D
Join us on Facebook
http://www.facebook.com/home.php?sk=group_137541156293768&ap=1

Project Evolution *** Project Complete **** Wednesday July 9, 2014

Reply #1655 –
So I pulled out another stock hood today. I think I'm going to make myself a custom hood this winter. but not sure what kind yet. And I'm not sure what car it's going on either.
[SIGPIC][/SIGPIC]
***** Project "EVOLUTION" 1987 Cougar LS  & 1985 Cougar Convertible *****
[/COLOR]
5.0 HO 306 roller block, machined GT-40P heads, Wiseco dished forged pistons, Eagle forged floating I-beam connecting rods, Lunati pushrods, ARP bolts, Scorpion aluminum 1.6 rockers, Comp Cams Magnum 266HR, Explorer intake, 65mm TB, MAF Conversion, 19# injectors, Ford Racing stainless P-headers, 2-1/2" cat-less exhaust w/ Flowtech Afterburner lers , SC AOD with 2800 BDR torque converter, 3.73 T-Lok rear, CHE rear control arms, full 2-1/2" frame w/1" jacking rails & seat supports, Rear disk brakes, Turbine wheels, All original interior w/ floor shift upgrade .......
Pretty much every panel on my 87 is new, rebuilt, or re constructed. :D
Join us on Facebook
http://www.facebook.com/home.php?sk=group_137541156293768&ap=1

Project Evolution *** Project Complete **** Wednesday July 9, 2014

Reply #1656 –
yeah i plan on it. got my new dd up and running again. (replaced trans)  but i will be up there on friday so if i stay pver i can come up sat to get those and help ya out if ya need it.
2001 Buick Regal LS (DD):hick:

Got that fox rash again!

-Resident smartass! :ies:

- Don't listen to the naysayers. For every person who actually helps with your project there will be 10 who will discourage you all the while thinking that they are helping. 99% of all people have good intentions. That doesn't make them right.- XR7 Dave - SCCOA.Com

Project Evolution *** Project Complete **** Wednesday July 9, 2014

Reply #1657 –
did some putting away. One step closer to getting back to work on the car. Here I pushed the vert next to the wall so I can get the Lincoln in for the winter. I'll probably pull it out again to drive it before it gets put away until spring. Thinking about putting some plastic down on the floor when I do. I'll paint the entire floor next summer. Can't believe how big it is in there when it's empty.


And while I had the 87 pushed to the other side of the garage, I decided to take a pic of it. I never really could step back and look at this side while working on it.


So I figure 1, maybe 2 weekends at the most before I can resume what I had started. And yes, It's really clean in there now. All the stuff for work is now gone, and now the garage is just for cars. I can get all 3 in, and I still have an entire cabinet shop on the new side.
That's my update. Also have some new presents for my car for Christmas. I'll share as they arrive. :D
[SIGPIC][/SIGPIC]
***** Project "EVOLUTION" 1987 Cougar LS  & 1985 Cougar Convertible *****
[/COLOR]
5.0 HO 306 roller block, machined GT-40P heads, Wiseco dished forged pistons, Eagle forged floating I-beam connecting rods, Lunati pushrods, ARP bolts, Scorpion aluminum 1.6 rockers, Comp Cams Magnum 266HR, Explorer intake, 65mm TB, MAF Conversion, 19# injectors, Ford Racing stainless P-headers, 2-1/2" cat-less exhaust w/ Flowtech Afterburner lers , SC AOD with 2800 BDR torque converter, 3.73 T-Lok rear, CHE rear control arms, full 2-1/2" frame w/1" jacking rails & seat supports, Rear disk brakes, Turbine wheels, All original interior w/ floor shift upgrade .......
Pretty much every panel on my 87 is new, rebuilt, or re constructed. :D
Join us on Facebook
http://www.facebook.com/home.php?sk=group_137541156293768&ap=1

Project Evolution *** Project Complete **** Wednesday July 9, 2014

Reply #1658 –
I need a bigger garage :D
88 Thunderbird LX: 306, Edelbrock Performer heads, Comp 266HR cam, Edelbrock Performer RPM intake, bunch of other stuff.

Project Evolution *** Project Complete **** Wednesday July 9, 2014

Reply #1659 –
 Jerry, that's some cowl hood on that '87...
2015 Mustang GT Premium - 5.0, 6-speed, Guard Green - too much awesome for one car

1988 5.0 Thunderbird :birdsmily: SOLD SEPT 11 2010: TC front clip/hood ♣ Body & paint completed Oct 2007 ♣ 3.55 TC rear end and front brakes ♣ TC interior ♣ CHE rear control arms (adjustable lowers) ♣ 2001 Bullitt springs ♣ Energy suspension poly busings ♣ Kenne Brown subframe connectors ♣ CWE engine mounts ♣ Thundercat sequential turn signals ♣ Explorer overhead console (temp/compass display) ♣ 2.25" off-road dual exhaust ♣ T-5 transmission swap completed Jan 2009 ♣

Project Evolution *** Project Complete **** Wednesday July 9, 2014

Reply #1660 –
Yea seriously!! You'd better be putting a tunnel ram'd 514 in there or something....:rollin:
1987 20th Anniversary Cougar, 302 "5.0" GT-40 heads (F3ZE '93 Cobra) and TMoss Ported H.O. intake, H.O. camshaft
2.5" Duals, no cats, Flowmaster 40s, Richmond 3.73s w/ Trac-Lok, maxed out Baumann shift kit, 3000 RPM Dirty Dog non-lock TC
Aside from the Mustang crinkle headers, still looks like it's only 150 HP...
1988 Black XR7 Trick Flow top end, Tremec 3550
1988 Black XR7 Procharger P600B intercooled, Edelbrock Performer non-RPM heads, GT40 intake AOD, 13 PSI @5000 RPM. 93 octane

Project Evolution *** Project Complete **** Wednesday July 9, 2014

Reply #1661 –
I guess we'll just have to see what's going in there now. ;)
[SIGPIC][/SIGPIC]
***** Project "EVOLUTION" 1987 Cougar LS  & 1985 Cougar Convertible *****
[/COLOR]
5.0 HO 306 roller block, machined GT-40P heads, Wiseco dished forged pistons, Eagle forged floating I-beam connecting rods, Lunati pushrods, ARP bolts, Scorpion aluminum 1.6 rockers, Comp Cams Magnum 266HR, Explorer intake, 65mm TB, MAF Conversion, 19# injectors, Ford Racing stainless P-headers, 2-1/2" cat-less exhaust w/ Flowtech Afterburner lers , SC AOD with 2800 BDR torque converter, 3.73 T-Lok rear, CHE rear control arms, full 2-1/2" frame w/1" jacking rails & seat supports, Rear disk brakes, Turbine wheels, All original interior w/ floor shift upgrade .......
Pretty much every panel on my 87 is new, rebuilt, or re constructed. :D
Join us on Facebook
http://www.facebook.com/home.php?sk=group_137541156293768&ap=1

Project Evolution *** Project Complete **** Wednesday July 9, 2014

Reply #1662 –
I'm jealous! I've been cleaning in the garage too, but for a very different reason. We've been cleaning and packing all of our "extra" stuff to ready the house to go on the market in January.

Shiny Side Up!
Bill
"as if 'religion' were something God invented, and not His statement to us of certain quite unalterable facts about His own nature." -C.S. Lewis

Project Evolution *** Project Complete **** Wednesday July 9, 2014

Reply #1663 –
Jerry, anytime you want to come over and build a garage for me, I'll make sure to keep it clean.  Then I can play this "see what's going in there" game, too.  LOL.  BTW, I cleared a spot for it already.
1987 TC

Project Evolution *** Project Complete **** Wednesday July 9, 2014

Reply #1664 –
I'm jealous, and you got heat.
Old Grey Cat to this.88 Cat, 5.0 HO, CW mounts, mass air, CI custom cam, afr165's, Tmoss worked cobra intake, BBK shorty's,off road h pipe, magnaflow ex. T-5,spec stage 2 clutch, 8.8 373 TC trac loc, che ajustables with bullits on the rear. 11" brakes up front. +