Skip to main content ↑ ↓
Topic: Pulled Code From ATC System, Still looking for Condenser Drain... (Read 2930 times) previous topic - next topic

Pulled Code From ATC System, Still looking for Condenser Drain...

Reply #15 –
How does one locate this Condenser Drain? I should also mention that I attempted to get the heater to turn on by setting the Temp to 90 degrees, but I couldn't get any hot air to blow from the vents.
<---One must always remember to Remain cool, calm and collected when dealing with your fellow man, especially on the Internet....
-DMC24guy
[/SIZE]

Pulled Code From ATC System, Still looking for Condenser Drain...

Reply #16 –
I pulled the following Code from the ATC system:

05     Blend actuator over current.

Now what? Oh yeah, I still don't know where the Condenser Drain is located???
<---One must always remember to Remain cool, calm and collected when dealing with your fellow man, especially on the Internet....
-DMC24guy
[/SIZE]

Pulled Code From ATC System, Still looking for Condenser Drain...

Reply #17 –
condensor drain will be on the pass lower area of the firewall  near the exhaust manifold /pipe .
[SIGPIC][/SIGPIC]
1974 maverick lsx powered turbo car SOLD
1973 maverick Tijuana Taxi Tribute
1957 chevy LSX Turbo project (race car)
Owner of Joe Dirt Fabrication

Pulled Code From ATC System, Still looking for Condenser Drain...

Reply #18 –
Little rubber plug about 1-1/2" diameter, stubby hose in the middle.
.
Death awaits you all with nasty, big, pointy teeth.

1988 5.0 Bird, mostly stock, partly not, now gone to T-Bird heaven.
1990 Volvo 740GL. 114 tire-shredding horsies, baby!

Pulled Code From ATC System, Still looking for Condenser Drain...

Reply #19 –
Well, I took a wire to the Drain plug and sure enough, when I pushed it through, a bunch of water came spewing out. Problem solved.

Now to the next item of business, what does my ATC code mean?
05 Blend actuator over current.
<---One must always remember to Remain cool, calm and collected when dealing with your fellow man, especially on the Internet....
-DMC24guy
[/SIZE]
 

Pulled Code From ATC System, Still looking for Condenser Drain...

Reply #20 –
The "blend" door is the one that manages temperature (by blending hot and cold air). Yours may be stuck, which would explain not getting cold enough air (it may be blending a bit of hot air in), or the actuator motor may be shorted. Either situation would result in the overcurrent situation, as sending power to an electric motor that can't move will cause high current
2015 Mustang GT Premium - 5.0, 6-speed, Guard Green - too much awesome for one car

1988 5.0 Thunderbird :birdsmily: SOLD SEPT 11 2010: TC front clip/hood ♣ Body & paint completed Oct 2007 ♣ 3.55 TC rear end and front brakes ♣ TC interior ♣ CHE rear control arms (adjustable lowers) ♣ 2001 Bullitt springs ♣ Energy suspension poly busings ♣ Kenne Brown subframe connectors ♣ CWE engine mounts ♣ Thundercat sequential turn signals ♣ Explorer overhead console (temp/compass display) ♣ 2.25" off-road dual exhaust ♣ T-5 transmission swap completed Jan 2009 ♣

Pulled Code From ATC System, Still looking for Condenser Drain...

Reply #21 –
Well, what should be my next move?
<---One must always remember to Remain cool, calm and collected when dealing with your fellow man, especially on the Internet....
-DMC24guy
[/SIZE]

Pulled Code From ATC System, Still looking for Condenser Drain...

Reply #22 –
I dunno, haven't done much work on the ATC systems in these things, but my guess would be to pull the actuator off (but leave it plugged in) and see if you can move the flap by hand. Also try moving the motor with the EATC controller...
2015 Mustang GT Premium - 5.0, 6-speed, Guard Green - too much awesome for one car

1988 5.0 Thunderbird :birdsmily: SOLD SEPT 11 2010: TC front clip/hood ♣ Body & paint completed Oct 2007 ♣ 3.55 TC rear end and front brakes ♣ TC interior ♣ CHE rear control arms (adjustable lowers) ♣ 2001 Bullitt springs ♣ Energy suspension poly busings ♣ Kenne Brown subframe connectors ♣ CWE engine mounts ♣ Thundercat sequential turn signals ♣ Explorer overhead console (temp/compass display) ♣ 2.25" off-road dual exhaust ♣ T-5 transmission swap completed Jan 2009 ♣

Pulled Code From ATC System, Still looking for Condenser Drain...

Reply #23 –
Quote from: DMC24guy
Well, what should be my next move?

close or open the door manually.
[SIGPIC][/SIGPIC]
1974 maverick lsx powered turbo car SOLD
1973 maverick Tijuana Taxi Tribute
1957 chevy LSX Turbo project (race car)
Owner of Joe Dirt Fabrication

Pulled Code From ATC System, Still looking for Condenser Drain...

Reply #24 –
Does anyone have a schematic of any kind that shows the physical location of the various ATC actuators?  I think that one of them is directly behind the glove box door but I am not sure about any of the others.
-Jim
1987 Cougar LS 5.0

Pulled Code From ATC System, Still looking for Condenser Drain...

Reply #25 –
Quote from: jkirchman
Does anyone have a schematic of any kind that shows the physical location of the various ATC actuators?  I think that one of them is directly behind the glove box door but I am not sure about any of the others.

Here ya go - sorry for the poor image quality, I think Mitchell1 used old faxes for these diagrams...
2015 Mustang GT Premium - 5.0, 6-speed, Guard Green - too much awesome for one car

1988 5.0 Thunderbird :birdsmily: SOLD SEPT 11 2010: TC front clip/hood ♣ Body & paint completed Oct 2007 ♣ 3.55 TC rear end and front brakes ♣ TC interior ♣ CHE rear control arms (adjustable lowers) ♣ 2001 Bullitt springs ♣ Energy suspension poly busings ♣ Kenne Brown subframe connectors ♣ CWE engine mounts ♣ Thundercat sequential turn signals ♣ Explorer overhead console (temp/compass display) ♣ 2.25" off-road dual exhaust ♣ T-5 transmission swap completed Jan 2009 ♣

Pulled Code From ATC System, Still looking for Condenser Drain...

Reply #26 –
Thank you Carm!  You have now confirmed my suspicion that the blend door actuator is buried beneath the dash to a point where it is virtually inaccesible!
-Jim
1987 Cougar LS 5.0

Pulled Code From ATC System, Still looking for Condenser Drain...

Reply #27 –
Well that's exactly what I wanted to hear. I need to tear up my Dash to get to the thing....

Hey, my car is equiped with the fully Electronic Cluster (Tach, Fuel Economy, etc). If I were to find one of those buttstuffog clusters off an 88 Sport or XR7, could I place it directly in without going through the rewiring hell I had to deal with when putting the Turbo Cluster in my v6? (I'm asking this because I was doing some tests with other cars...and a cop....and I found out my Electronic Speedometer is reading 5 mph slow. I.E., I'm really doing 45 when it's showing 40. And that's never good.....)
<---One must always remember to Remain cool, calm and collected when dealing with your fellow man, especially on the Internet....
-DMC24guy
[/SIZE]

Pulled Code From ATC System, Still looking for Condenser Drain...

Reply #28 –
Umm.. if you put an buttstuffog cluster in it will read 5 mph off as well.
One 88