Skip to main content
Topic: Door window problem, help! (Read 2005 times) previous topic - next topic

Door window problem, help!

Hello, everyone, I am new here. 
I have an 87 Cougar with the typical window issue.
I have had it fixed before, but this time one of the
clips broke. :-(
Is there anywhere that sells replacement clips?

Door window problem, help!

Reply #1
Dorman has them.

Check for them at autozone or orileys in the "help" section.
Quote from: jcassity
I honestly dont think you could exceed the cost of a new car buy installing new *stock* parts everywhere in your coug our tbird. Its just plain impossible. You could revamp the entire drivetrain/engine/suspenstion and still come out ahead.
Hooligans! 
1988 Crown Vic wagon. 120K California car. Wifes grocery getter. (junked)
1987 Ford Thunderbird LX. 5.0. s.o., sn-95 t-5 and an f-150 clutch. Driven daily and going strong.
1986 cougar.
lilsammywasapunkrocker@yahoo.com

Door window problem, help!

Reply #2
then use high quality silicone in the cradles,, then clean your vertical tracks,, then roll up the window,,, then don't lower it for a day.

Door window problem, help!

Reply #3
Also sand/scuff up the glass before epoxy or whatever you use.  Lube up and make sure your tracks are clean and not binding.  I think last time I used Goop automotive adhesive, been holding good for years now.  Prob just jinxed myself
Mike

Door window problem, help!

Reply #4
Thanks, guys!  Never thought to scan the HELP section for them.
Really appreciate all the info!  :)

Door window problem, help!

Reply #5
How do you get them to go up and down easy?
[SIGPIC][/SIGPIC]:ford:87 Turbo Coupe through the floor sub frame connectors, 5.8 swap Ford racing heads Harland sharp 1.6 rockers BBK shorty swap headers 2 1/2 BBk X pipe magnaflow ler's. Megasquirt 2 with 36lbs injectors on hurricane intake with 4150 throttle body.Tremec TKO 600 Quicktime blowsheild spec stage 3 clutch. 3.73 gears and still not done

Door window problem, help!

Reply #6
How do you get them to go up and down easy?
[SIGPIC][/SIGPIC]:ford:87 Turbo Coupe through the floor sub frame connectors, 5.8 swap Ford racing heads Harland sharp 1.6 rockers BBK shorty swap headers 2 1/2 BBk X pipe magnaflow ler's. Megasquirt 2 with 36lbs injectors on hurricane intake with 4150 throttle body.Tremec TKO 600 Quicktime blowsheild spec stage 3 clutch. 3.73 gears and still not done



Door window problem, help!

Reply #9
Ok because you are new here goes. My full length window channels are the only fix. As you posted you had it fixed before. Only way is this way .
Doorman ones are garbage and i have tried every chemical on this planet. Bottom line the clips are to small. Now we can thrash it around again for a couple of days. have a great evening guys

.


I spend money I don't have, To build  cars I don't need, To impress people I don't know

HAVE YOU DRIVEN A FORD LATELY!!

 

Door window problem, help!

Reply #10
You gonna start marketing those?  I'd buy a set.

I've been lucky with aquarium grade silicone.  It's been holding on the passenger window for about 5 years now.  The driver side even longer.
-- 05 Mustang GT-Whipplecharged !!
--87 5.0 Trick Flow Heads & Intake - Custom Cam - Many other goodies...3100Lbs...Low12's!