Skip to main content
Topic: ! I found rust ! (Read 1204 times) previous topic - next topic

! I found rust !

Finally warmed up enough that I thought I'd play around in the garage. I was looking around the car, daydreamin' different colors and stripes etc. Looked thru the grill opening, the  bottom of the core support looks like it came from the bottom of a lake !!!
Crusty flakes and holes ! No rust anywhere else, just the core support ! :punchballs:
There's a couple of them in the local Pull-A-Part, is this an easy removal / install ?
88 Sport ,306 roller block, flat tops, ARP rods and bolts, Compcam 533 lift/ 270 duration, roller rockers, ported 351w heads with 1.94 - 1.60 valves, 550 springs, 600cfm carb , full length headers, 2.5" dual X-pipe exhaust, MSD ignition, Hughes built C4, Weld Draglites, Tracloc /Richmond 3:73's

! I found rust !

Reply #1
You'll need a tack weld removal bit.I've seen a few swapped by the Northern guys.We don't have those issues here.
'88 Sport--T-5,MGW shifter,Trick Flow R intake,Ed Curtis cam,Trick Flow heads,Scorpion rockers,75mm Accufab t-body,3G,mini starter,Taurus fan,BBK long tube headers,O/R H-Pipe, Flowamaster Super 44's, deep and deeper Cobra R wheels, Mass Air and 24's,8.8 with 3.73's,140 mph speedo,Mach 1 chin spoiler,SN-95 springs,CHE control arms,aluminum drive shaft and a lot more..

! I found rust !

Reply #2
It's weird, the sides of the support are great. It's just the very bottom of it. I may just scavenge that section and weld it in.
88 Sport ,306 roller block, flat tops, ARP rods and bolts, Compcam 533 lift/ 270 duration, roller rockers, ported 351w heads with 1.94 - 1.60 valves, 550 springs, 600cfm carb , full length headers, 2.5" dual X-pipe exhaust, MSD ignition, Hughes built C4, Weld Draglites, Tracloc /Richmond 3:73's

! I found rust !

Reply #3
of course you know I replaced most of the front end.
you need to replace one of these?


[SIGPIC][/SIGPIC]
***** Project "EVOLUTION" 1987 Cougar LS  & 1985 Cougar Convertible *****
[/COLOR]
5.0 HO 306 roller block, machined GT-40P heads, Wiseco dished forged pistons, Eagle forged floating I-beam connecting rods, Lunati pushrods, ARP bolts, Scorpion aluminum 1.6 rockers, Comp Cams Magnum 266HR, Explorer intake, 65mm TB, MAF Conversion, 19# injectors, Ford Racing stainless P-headers, 2-1/2" cat-less exhaust w/ Flowtech Afterburner lers , SC AOD with 2800 BDR torque converter, 3.73 T-Lok rear, CHE rear control arms, full 2-1/2" frame w/1" jacking rails & seat supports, Rear disk brakes, Turbine wheels, All original interior w/ floor shift upgrade .......
Pretty much every panel on my 87 is new, rebuilt, or re constructed. :D
Join us on Facebook

! I found rust !

Reply #4
daminc, that's exactly the area of mine that is bad.
I'm debating whether or not to let it go till winter rolls around again.
88 Sport ,306 roller block, flat tops, ARP rods and bolts, Compcam 533 lift/ 270 duration, roller rockers, ported 351w heads with 1.94 - 1.60 valves, 550 springs, 600cfm carb , full length headers, 2.5" dual X-pipe exhaust, MSD ignition, Hughes built C4, Weld Draglites, Tracloc /Richmond 3:73's

! I found rust !

Reply #5
if it's still in 1 piece and not flapping, you should have no problem with waiting until winter. This was mine and it was still supporting

[SIGPIC][/SIGPIC]
***** Project "EVOLUTION" 1987 Cougar LS  & 1985 Cougar Convertible *****
[/COLOR]
5.0 HO 306 roller block, machined GT-40P heads, Wiseco dished forged pistons, Eagle forged floating I-beam connecting rods, Lunati pushrods, ARP bolts, Scorpion aluminum 1.6 rockers, Comp Cams Magnum 266HR, Explorer intake, 65mm TB, MAF Conversion, 19# injectors, Ford Racing stainless P-headers, 2-1/2" cat-less exhaust w/ Flowtech Afterburner lers , SC AOD with 2800 BDR torque converter, 3.73 T-Lok rear, CHE rear control arms, full 2-1/2" frame w/1" jacking rails & seat supports, Rear disk brakes, Turbine wheels, All original interior w/ floor shift upgrade .......
Pretty much every panel on my 87 is new, rebuilt, or re constructed. :D
Join us on Facebook

! I found rust !

Reply #6
If I'd clean up the flaking it would probably look like your old one. Is the core support the same in the Mustangs or is it T-Bird specific ?
88 Sport ,306 roller block, flat tops, ARP rods and bolts, Compcam 533 lift/ 270 duration, roller rockers, ported 351w heads with 1.94 - 1.60 valves, 550 springs, 600cfm carb , full length headers, 2.5" dual X-pipe exhaust, MSD ignition, Hughes built C4, Weld Draglites, Tracloc /Richmond 3:73's

! I found rust !

Reply #7
I believe they're diff, but not sure about just replacing only the bottom. that part may be usable. (unless they're narrower)
[SIGPIC][/SIGPIC]
***** Project "EVOLUTION" 1987 Cougar LS  & 1985 Cougar Convertible *****
[/COLOR]
5.0 HO 306 roller block, machined GT-40P heads, Wiseco dished forged pistons, Eagle forged floating I-beam connecting rods, Lunati pushrods, ARP bolts, Scorpion aluminum 1.6 rockers, Comp Cams Magnum 266HR, Explorer intake, 65mm TB, MAF Conversion, 19# injectors, Ford Racing stainless P-headers, 2-1/2" cat-less exhaust w/ Flowtech Afterburner lers , SC AOD with 2800 BDR torque converter, 3.73 T-Lok rear, CHE rear control arms, full 2-1/2" frame w/1" jacking rails & seat supports, Rear disk brakes, Turbine wheels, All original interior w/ floor shift upgrade .......
Pretty much every panel on my 87 is new, rebuilt, or re constructed. :D
Join us on Facebook

! I found rust !

Reply #8
Another place to watch out for...seems somewhat common at least on northeast cars.
tbirdregistry.com
26480
27373

 

! I found rust !

Reply #9
yes,, they do rust a bit in that area.
[SIGPIC][/SIGPIC]
***** Project "EVOLUTION" 1987 Cougar LS  & 1985 Cougar Convertible *****
[/COLOR]
5.0 HO 306 roller block, machined GT-40P heads, Wiseco dished forged pistons, Eagle forged floating I-beam connecting rods, Lunati pushrods, ARP bolts, Scorpion aluminum 1.6 rockers, Comp Cams Magnum 266HR, Explorer intake, 65mm TB, MAF Conversion, 19# injectors, Ford Racing stainless P-headers, 2-1/2" cat-less exhaust w/ Flowtech Afterburner lers , SC AOD with 2800 BDR torque converter, 3.73 T-Lok rear, CHE rear control arms, full 2-1/2" frame w/1" jacking rails & seat supports, Rear disk brakes, Turbine wheels, All original interior w/ floor shift upgrade .......
Pretty much every panel on my 87 is new, rebuilt, or re constructed. :D
Join us on Facebook