installed mustang tubular a arms... March 02, 2006, 08:57:55 PM what a nightmare, i only did one side because after letting the car down the new a arm moved the wheel and tire in like 2" and it doesnt even look like the alignment could ever be made right, not to mention how stupid it looks with the wheel/tire in so far. AHHHHHHHHHHHHHHHH, 190 dollar arms, wtf am i gonna do..atleast my GMS coil over kit works. just need caster camber plates... Quote Selected
installed mustang tubular a arms... Reply #1 – March 02, 2006, 09:18:58 PM who's the manufacturer? Quote Selected
installed mustang tubular a arms... Reply #2 – March 02, 2006, 09:38:57 PM What k-member are you using? Thanks, Chris Quote Selected
installed mustang tubular a arms... Reply #3 – March 02, 2006, 09:55:22 PM were they fox mustang arms, or sn-95? Quote Selected
installed mustang tubular a arms... Reply #4 – March 02, 2006, 10:05:15 PM If I'm not mistaken (and I have been mistaken before, believe it or not), a Mustang K-member will put your ball joints back out close to where they belong. I think the T-Bird K-member's control arm mounting points are further inboard to work with the longer T-Bird arms, so Mustang arms will bring the ball joints in on a T-Bird member. Conversely, T-Bird arms on a Mustang member will put the ball joints outboard. I'm sure somebody that knows what the hell they are talking about will chime in for verification though... Quote Selected
installed mustang tubular a arms... Reply #5 – March 02, 2006, 10:14:06 PM ChuckW has stated that many times already what ThunderChicken just said.You are 100% correct. Quote Selected
installed mustang tubular a arms... Reply #6 – March 02, 2006, 10:19:13 PM have to run a stang k member..... Quote Selected
installed mustang tubular a arms... Reply #7 – March 03, 2006, 08:08:12 AM Aren't the SN-95 A-arms the same dimensions as the fox t-bird/cougar arms? Quote Selected
installed mustang tubular a arms... Reply #8 – March 03, 2006, 08:29:44 AM Quote from: Paul FlockhartAren't the SN-95 A-arms the same dimensions as the fox t-bird/cougar arms?Not quite .. the 87-88's do at least. The early Tbirds use the Fox Mustang arms...Also, be careful on the whole "TBird K-member" thing. The different mounting points only applies to the 87-88's.....and only the TC's at that.I'm not 100% certain on the whole 87-88 TC only thing, but since we have not had as a group everyone with an 86-88 climb under their car and measure the width of the control arm mounting points and the length of their control arms :p Quote Selected
installed mustang tubular a arms... Reply #9 – March 03, 2006, 09:25:26 AM yeah im using the stock K member, that must be my problem? Quote Selected
installed mustang tubular a arms... Reply #10 – March 03, 2006, 10:39:04 AM At the very least then you need SN-95 length tubular arms.... Quote Selected
installed mustang tubular a arms... Reply #11 – March 03, 2006, 06:30:41 PM Perfect time for a tubular fox stang k member! Quote Selected
installed mustang tubular a arms... Reply #12 – March 06, 2006, 12:33:46 PM with the mustang tubular K what do i use for motor mounts? Quote Selected
installed mustang tubular a arms... Reply #13 – March 06, 2006, 12:48:24 PM well guessing it is for a mustang, I would say a 79-93 4banger, or maybe 84 SVO mounts. I am not quite sure. Quote Selected
installed mustang tubular a arms... Reply #14 – March 06, 2006, 01:38:45 PM A set of my SVO/Mustang mounts :DSeriously though, you would use any of the std Mustang 4 cyl mounts. Quote Selected
Topic: installed mustang tubular a arms... (Read 4059 times)
previous topic - next topic
