This should be a no Brainer Right ? 88 T-Bird 5.0 July 19, 2014, 07:12:36 PM Guys driver side left turn signal are not flashing but they are Solid - the rear left turn signals work - the dash flashes leftfront passenger right turn are flashing and so are the rearthis is the bulb ?the relay ?fuse ?I say the bulb - if so, is there another Trade number I can use that will work instead of 3157 (Natural Amber) - Quote Selected
This should be a no Brainer Right ? 88 T-Bird 5.0 Reply #1 – July 19, 2014, 08:30:29 PM I'm betting a bulb. You can get bulbs in amber and clear. Quote Selected
This should be a no Brainer Right ? 88 T-Bird 5.0 Reply #2 – July 19, 2014, 10:45:47 PM Canadian models have different signal light requirements... Quote Selected
This should be a no Brainer Right ? 88 T-Bird 5.0 Reply #3 – July 19, 2014, 11:14:29 PM I am not following your post one bit. Does the left side front and rear light up and also the dash when selecting a left turn from the turn signal handle??? I think youare basically saying they front and rear light but do not flash. Is this the situation?? Quote Selected
This should be a no Brainer Right ? 88 T-Bird 5.0 Reply #4 – July 20, 2014, 07:04:29 AM Sounds like just the front isn't flashing ,but the dash indicates it is? Incorrect bulb? Quote Selected
This should be a no Brainer Right ? 88 T-Bird 5.0 Reply #5 – July 20, 2014, 08:53:56 PM Do the parking or headlights have to be on for this to happen?Do you have daytime running lights in Canada? Quote Selected
This should be a no Brainer Right ? 88 T-Bird 5.0 Reply #6 – July 20, 2014, 10:42:48 PM Basically i have no clue what he is talking about. Can someone enlighten me on his issue??????????? Quote Selected
This should be a no Brainer Right ? 88 T-Bird 5.0 Reply #7 – July 21, 2014, 12:14:00 PM Tom .... BasicallyThe left front lamps 3157(NA) won't flash when I turn left they just stay solid - everything else on the car lights and signals works finethe dash flashs like it should just no lights flashing in the front left - the back yesThe headlights can be on or off it doesn't matter and it does have daytime running lights if I push the head lights button half way Quote Selected
This should be a no Brainer Right ? 88 T-Bird 5.0 Reply #8 – July 21, 2014, 12:53:29 PM I think the reason we are confused is this: In our cars, in America, there are two filaments in the bulb, the parking light filament, and the flasher/brake filament. I don't have a schematic in front of me, but IIRC, the turn flasher filaments are in parallel; front with the rear. The front and rear turn signals cannot act independently. If this was an American car, the only way the front can be solid with the rear flashing, is you have the parking/headlamps on, and you are seeing that filament lit, and the flasher filament is burned out. To further confuse the issue, I believe when one flasher filament burns out, the circuit doesn't draw enough current to heat the flasher plug and the remaining bulb (and the dash indicator) would also light solid, but I digress...Short answer, for us Americans, the only answer in that situation would be, replace the bulb. If Canadian wiring is different, then I don't know Easy way to tell, just swap the bulb from the other side and see if the problem switches sides. Quote Selected
This should be a no Brainer Right ? 88 T-Bird 5.0 Reply #9 – July 21, 2014, 04:43:54 PM I will try this - thank you I will let you know how this turns outI should have pics up of my 88 Restored, perhaps tonight. :-) Quote Selected
This should be a no Brainer Right ? 88 T-Bird 5.0 Reply #10 – July 21, 2014, 05:52:29 PM Pull out the turn signal lever connector and focus on light green wire with white stripe. That's for front left turn signal lamp. Check this wire with your multimeter in ohm reading. You can compare it with White wire with light blue stripe. That's for front right lamp. They both should have almost the same reading. If they don't, trace that wire and try to find a problem. These wires goes in the loom on the drivers side of engine bay and have a grey connector next to the battery tray (closer to the firewall). Quote Selected
This should be a no Brainer Right ? 88 T-Bird 5.0 Reply #11 – July 28, 2014, 09:30:00 PM Stupid Bulb was all it was - Whew Thank God it was that simple Quote Selected
This should be a no Brainer Right ? 88 T-Bird 5.0 Reply #12 – July 29, 2014, 06:43:39 AM So basically he had a bad secondary filament in the 3157. Or another words on the high side filament on the signal side of the lamp. Basically he was checking it with his dims on and they stayed normal as the 3157 is a duel filament lamp. Explaining this issue was beyond me when he posted it. naturally the high side of the LAMP was OUT!!! have a great day guys Quote Selected
This should be a no Brainer Right ? 88 T-Bird 5.0 Reply #13 – August 01, 2014, 12:50:56 PM Well, checking bulbs should be mandatory before posting such a question. I guess everyone expected the check has been done, that's the reason why we are asking much more delicate questions and looking for possible (non present) issue. :( Quote Selected