Skip to main content ↑ ↓
Topic: porting tools? (Read 794 times) previous topic - next topic

porting tools?

So i have a couple different electric die grinders but only one is adjustable but that only has a 1/8 drive and its bits arent very long so it cant get very deep. The other one spins at 30,000rpm and just blows the rolled up sandpaper bits away pretty quickly. Any suggestions?
1987 turbo coupe 5speed: Boport stage 3 head/2.5 cam , Precision stage 3 50trim .63 turbo, Tial 38mm wastegate, Jangus gutted/ported intake manifolds, 60mm tb, Jangus open dumptube, Jangus 3" elbow, Perrin boost controller,Esslinger adjustable cam pulley, Esslinger small crank pulley, stinger FMI, RFL BOV, Spec stage 3 clutch, B&M short throw, 140 speedo, Walbo 255lph, BBK fpr, 3G alternator, ARP studs.  Be faster... :poke:

porting tools?

Reply #1 –
Find a speed controller that plugs in between the electrical outlet and the tool. It will allow you to limit the amout of juice going to the tool which will slow it down.
88 TC 5speed, 168000+ miles, stock 2.3T long block, ported RFE6 exhaust, Evergreen T3 running 15#'s.
Up next: FMIC, fresh air intake, ported intakes, ported big valve head.

porting tools?

Reply #2 –
All i can find is speed controllers for fans
1987 turbo coupe 5speed: Boport stage 3 head/2.5 cam , Precision stage 3 50trim .63 turbo, Tial 38mm wastegate, Jangus gutted/ported intake manifolds, 60mm tb, Jangus open dumptube, Jangus 3" elbow, Perrin boost controller,Esslinger adjustable cam pulley, Esslinger small crank pulley, stinger FMI, RFL BOV, Spec stage 3 clutch, B&M short throw, 140 speedo, Walbo 255lph, BBK fpr, 3G alternator, ARP studs.  Be faster... :poke:

porting tools?

Reply #3 –
I don't shop at Harbor Freight very often, but they have what they call a router speed controller that would work for what you need.
88 TC 5speed, 168000+ miles, stock 2.3T long block, ported RFE6 exhaust, Evergreen T3 running 15#'s.
Up next: FMIC, fresh air intake, ported intakes, ported big valve head.

porting tools?

Reply #4 –
Oh okay cool. Thank you Jangus.
1987 turbo coupe 5speed: Boport stage 3 head/2.5 cam , Precision stage 3 50trim .63 turbo, Tial 38mm wastegate, Jangus gutted/ported intake manifolds, 60mm tb, Jangus open dumptube, Jangus 3" elbow, Perrin boost controller,Esslinger adjustable cam pulley, Esslinger small crank pulley, stinger FMI, RFL BOV, Spec stage 3 clutch, B&M short throw, 140 speedo, Walbo 255lph, BBK fpr, 3G alternator, ARP studs.  Be faster... :poke:

porting tools?

Reply #5 –
what amp should it be? I have found 10, 15 and 20 amp controllers
1987 turbo coupe 5speed: Boport stage 3 head/2.5 cam , Precision stage 3 50trim .63 turbo, Tial 38mm wastegate, Jangus gutted/ported intake manifolds, 60mm tb, Jangus open dumptube, Jangus 3" elbow, Perrin boost controller,Esslinger adjustable cam pulley, Esslinger small crank pulley, stinger FMI, RFL BOV, Spec stage 3 clutch, B&M short throw, 140 speedo, Walbo 255lph, BBK fpr, 3G alternator, ARP studs.  Be faster... :poke:
 

porting tools?

Reply #6 –
How many amps does your grinder pull? Match it.
88 TC 5speed, 168000+ miles, stock 2.3T long block, ported RFE6 exhaust, Evergreen T3 running 15#'s.
Up next: FMIC, fresh air intake, ported intakes, ported big valve head.