Skip to main content ↑ ↓
Topic: PCV Valve Plate for Intake (Read 447 times) previous topic - next topic

PCV Valve Plate for Intake

I need the plate which covers the hole where the PCV valve sits for an 87 Thunderbird 5.0. If you have one let me know, or know where to find one. I checked with summitt and Jegs to no avail. Ford surely doesn't have it.

PCV Valve Plate for Intake

Reply #1 –
What plate? It's a screen in the intake,a rubber grommet that slides into the intake on top of the screen,then the PCV valve which goes into the grommet. I got my grommet from O'Reillys.
'88 Sport--T-5,MGW shifter,Trick Flow R intake,Ed Curtis cam,Trick Flow heads,Scorpion rockers,75mm Accufab t-body,3G,mini starter,Taurus fan,BBK long tube headers,O/R H-Pipe, Flowamaster Super 44's, deep and deeper Cobra R wheels, Mass Air and 24's,8.8 with 3.73's,140 mph speedo,Mach 1 chin spoiler,SN-95 springs,CHE control arms,aluminum drive shaft and a lot more..

PCV Valve Plate for Intake

Reply #2 –
Hes looking for the Baffle on the  bottom of the  lower intake:D
Fox-less at the moment

PCV Valve Plate for Intake

Reply #3 –
I'd bet someone has a stock 5.0 intake laying around that they can either pull the baffle from,or sell the lower intake as a whole pretty cheap.
'88 Sport--T-5,MGW shifter,Trick Flow R intake,Ed Curtis cam,Trick Flow heads,Scorpion rockers,75mm Accufab t-body,3G,mini starter,Taurus fan,BBK long tube headers,O/R H-Pipe, Flowamaster Super 44's, deep and deeper Cobra R wheels, Mass Air and 24's,8.8 with 3.73's,140 mph speedo,Mach 1 chin spoiler,SN-95 springs,CHE control arms,aluminum drive shaft and a lot more..

PCV Valve Plate for Intake

Reply #4 –
Come to think of it,it would be really easy to fab one from sheet metal with simple tools.
'88 Sport--T-5,MGW shifter,Trick Flow R intake,Ed Curtis cam,Trick Flow heads,Scorpion rockers,75mm Accufab t-body,3G,mini starter,Taurus fan,BBK long tube headers,O/R H-Pipe, Flowamaster Super 44's, deep and deeper Cobra R wheels, Mass Air and 24's,8.8 with 3.73's,140 mph speedo,Mach 1 chin spoiler,SN-95 springs,CHE control arms,aluminum drive shaft and a lot more..

PCV Valve Plate for Intake

Reply #5 –
Quote from: vinnietbird;330722
Come to think of it,it would be really easy to fab one from sheet metal with simple tools.

And make it better. I made mine.
Old Grey Cat to this.88 Cat, 5.0 HO, CW mounts, mass air, CI custom cam, afr165's, Tmoss worked cobra intake, BBK shorty's,off road h pipe, magnaflow ex. T-5,spec stage 2 clutch, 8.8 373 TC trac loc, che ajustables with bullits on the rear. 11" brakes up front. +

PCV Valve Plate for Intake

Reply #6 –
I made one as well (thanks for the pattern Kitz).It's NICE (I have mad skills).
'88 Sport--T-5,MGW shifter,Trick Flow R intake,Ed Curtis cam,Trick Flow heads,Scorpion rockers,75mm Accufab t-body,3G,mini starter,Taurus fan,BBK long tube headers,O/R H-Pipe, Flowamaster Super 44's, deep and deeper Cobra R wheels, Mass Air and 24's,8.8 with 3.73's,140 mph speedo,Mach 1 chin spoiler,SN-95 springs,CHE control arms,aluminum drive shaft and a lot more..

PCV Valve Plate for Intake

Reply #7 –
It'd have to take the intake off again, correct? How did you guys attach it to the intake again? Anyone got pictures along the way of what you did, size, shape etc.

PCV Valve Plate for Intake

Reply #8 –
Me and Vin did it to cobra type intakes, not sure if it would work on a stock one, could be made to work. Look up wildBird on here and check his post, he has pics when he did his it was a few years since though, you may have do dig some for it.. I didn't take any. I do have the pattern for it I could email to you to try it.
Old Grey Cat to this.88 Cat, 5.0 HO, CW mounts, mass air, CI custom cam, afr165's, Tmoss worked cobra intake, BBK shorty's,off road h pipe, magnaflow ex. T-5,spec stage 2 clutch, 8.8 373 TC trac loc, che ajustables with bullits on the rear. 11" brakes up front. +

PCV Valve Plate for Intake

Reply #9 –
Is there anything I could do to stop it from coming up that would not involve taking the intake off again? IS there anything i could but on the bottom of the screen, like a "oil barrier" that would allow the car to vent but not allow the oil to come through? I don't want to have to rip everything apart again, I don't want to have to re-buy the complete gaskets kit, because its been adhered on, and if I disturb it, I'll have to do it all over again. Suggestions, thoughts?
 

PCV Valve Plate for Intake

Reply #10 –
Well what I did is I took the PCV valve, the grommet, and the screen out. I made a small circular piece of metal to sit in the grove underneath the screen. Hopefully this could act like a splash guard and still allow the fumes/vapors to come up. Time will tell.  Still open for other ideas just in case this doesn't work.