Skip to main content ↑ ↓
Topic: Anyone know where to get... (Read 1590 times) previous topic - next topic

Anyone know where to get...

the nuts that hold the body side molding pieces on ? Or, an alternative method of attaching them ?
Thanks
88 Sport ,306 roller block, flat tops, ARP rods and bolts, Compcam 533 lift/ 270 duration, roller rockers, ported 351w heads with 1.94 - 1.60 valves, 550 springs, 600cfm carb , full length headers, 2.5" dual X-pipe exhaust, MSD ignition, Hughes built C4, Weld Draglites, Tracloc /Richmond 3:73's

Anyone know where to get...

Reply #1 –
The rear or the front moldings?They are totally different.Let me know.I have to pick my wife up Wednesday out of town where my favorite yard is and i can grab some....along with a small list for a few fellow members.
'88 Sport--T-5,MGW shifter,Trick Flow R intake,Ed Curtis cam,Trick Flow heads,Scorpion rockers,75mm Accufab t-body,3G,mini starter,Taurus fan,BBK long tube headers,O/R H-Pipe, Flowamaster Super 44's, deep and deeper Cobra R wheels, Mass Air and 24's,8.8 with 3.73's,140 mph speedo,Mach 1 chin spoiler,SN-95 springs,CHE control arms,aluminum drive shaft and a lot more..

Anyone know where to get...

Reply #2 –
the guy before me used carpentry screws to put the molding back on, so now when it comes time im deleting the middle moldings between the front and back tires....

Anyone know where to get...

Reply #3 –
Quote from: vinnietbird;322682
The rear or the front moldings?They are totally different.Let me know.I have to pick my wife up Wednesday out of town where my favorite yard is and i can grab some....along with a small list for a few fellow members.


Vinnie, front and rear. Any chance you have pics ? I need to see how the front is supposed to look. The PO epoxied drywall screws to the backside of the ones I have.
88 Sport ,306 roller block, flat tops, ARP rods and bolts, Compcam 533 lift/ 270 duration, roller rockers, ported 351w heads with 1.94 - 1.60 valves, 550 springs, 600cfm carb , full length headers, 2.5" dual X-pipe exhaust, MSD ignition, Hughes built C4, Weld Draglites, Tracloc /Richmond 3:73's

Anyone know where to get...

Reply #4 –
The side molding between the front and rear wheels is stuck on with double sided tape.The front has metal nuts that one could get probably find at Lowe's,and the rear trim is held on with self cutting nuts that go over the plastic studs on the trim piece.I don't have any pics,but if you just look in the spare tire well in the trunk you can see what I'm talking about,and if you look under the hood down at the fender trim you can see the small etal nuts that hold it on.Metric threads for the front I believe.
'88 Sport--T-5,MGW shifter,Trick Flow R intake,Ed Curtis cam,Trick Flow heads,Scorpion rockers,75mm Accufab t-body,3G,mini starter,Taurus fan,BBK long tube headers,O/R H-Pipe, Flowamaster Super 44's, deep and deeper Cobra R wheels, Mass Air and 24's,8.8 with 3.73's,140 mph speedo,Mach 1 chin spoiler,SN-95 springs,CHE control arms,aluminum drive shaft and a lot more..

Anyone know where to get...

Reply #5 –
If you can not find it anywhere you could try this:  http://www.wesales.com/
-- 05 Mustang GT-Whipplecharged !!
--87 5.0 Trick Flow Heads & Intake - Custom Cam - Many other goodies...3100Lbs...Low12's!

Anyone know where to get...

Reply #6 –
Thanks V8Demon. Looks like a great place to get replacement fasteners.
88 Sport ,306 roller block, flat tops, ARP rods and bolts, Compcam 533 lift/ 270 duration, roller rockers, ported 351w heads with 1.94 - 1.60 valves, 550 springs, 600cfm carb , full length headers, 2.5" dual X-pipe exhaust, MSD ignition, Hughes built C4, Weld Draglites, Tracloc /Richmond 3:73's

Anyone know where to get...

Reply #7 –
Everything mentioned so far is correct. The problem is, most of the time it's not the fasteners that are missing in the rear, it's the plastic mounting studs themselves. They tend to twist off when you try to remove the "speed nuts" holding them on.
1987 Turbo Coupe - Son's car
1987 Super Coupe - Son's project car
1934 Ford - My project car

Anyone know where to get...

Reply #8 –
JBWeld some bolts to the trim piece then use standard nuts to hold it onto the car.
'88 Sport--T-5,MGW shifter,Trick Flow R intake,Ed Curtis cam,Trick Flow heads,Scorpion rockers,75mm Accufab t-body,3G,mini starter,Taurus fan,BBK long tube headers,O/R H-Pipe, Flowamaster Super 44's, deep and deeper Cobra R wheels, Mass Air and 24's,8.8 with 3.73's,140 mph speedo,Mach 1 chin spoiler,SN-95 springs,CHE control arms,aluminum drive shaft and a lot more..

Anyone know where to get...

Reply #9 –
Quote from: FLSTCI71;322760
Everything mentioned so far is correct. The problem is, most of the time it's not the fasteners that are missing in the rear, it's the plastic mounting studs themselves.


Yeah, that's how mine are. The outer sides look great though. Since they are being painted body color I was looking around for some way to just epoxy them right to the body. All the ones around here in the boneyards are pretty beat up or curled.
88 Sport ,306 roller block, flat tops, ARP rods and bolts, Compcam 533 lift/ 270 duration, roller rockers, ported 351w heads with 1.94 - 1.60 valves, 550 springs, 600cfm carb , full length headers, 2.5" dual X-pipe exhaust, MSD ignition, Hughes built C4, Weld Draglites, Tracloc /Richmond 3:73's
 

Anyone know where to get...

Reply #10 –
Quote from: vinnietbird;322775
JBWeld some bolts to the trim piece then use standard nuts to hold it onto the car.


Might be a better idea ! Will JB Weld stick to the plastic ?
88 Sport ,306 roller block, flat tops, ARP rods and bolts, Compcam 533 lift/ 270 duration, roller rockers, ported 351w heads with 1.94 - 1.60 valves, 550 springs, 600cfm carb , full length headers, 2.5" dual X-pipe exhaust, MSD ignition, Hughes built C4, Weld Draglites, Tracloc /Richmond 3:73's