Skip to main content ↑ ↓
Topic: trans cooler line leaking ? (Read 1250 times) previous topic - next topic

trans cooler line leaking ?

Its a 86 XR7 and I cant get the top cooler line at the radiator to stop leaking. It isnt leaking from the rad fitting but from the line at the nut.  Any suggestions will be greatly appreciated

trans cooler line leaking ?

Reply #1 –
Here is a pic of what I am speaking of. The leak is where the end of the screwdriver is. It appears there is sometype of plastic inset in the fitting. Hopefully someone will have some suggestions

trans cooler line leaking ?

Reply #2 –
autozone carries the part. I cant remember what it is, but it was cheap and fairly easy to get on. THe old one was harder to get off, and the new one just slid right over the line, no problems.
Quote from: jcassity
I honestly dont think you could exceed the cost of a new car buy installing new *stock* parts everywhere in your coug our tbird. Its just plain impossible. You could revamp the entire drivetrain/engine/suspenstion and still come out ahead.
Hooligans! 
1988 Crown Vic wagon. 120K California car. Wifes grocery getter. (junked)
1987 Ford Thunderbird LX. 5.0. s.o., sn-95 t-5 and an f-150 clutch. Driven daily and going strong.
1986 cougar.
lilsammywasapunkrocker@yahoo.com

trans cooler line leaking ?

Reply #3 –
Here you go, http://foxtbirdcougarforums.com/showthread.php?t=21912

You can buy the part at autozone. I think it was $3.
Quote from: jcassity
I honestly dont think you could exceed the cost of a new car buy installing new *stock* parts everywhere in your coug our tbird. Its just plain impossible. You could revamp the entire drivetrain/engine/suspenstion and still come out ahead.
Hooligans! 
1988 Crown Vic wagon. 120K California car. Wifes grocery getter. (junked)
1987 Ford Thunderbird LX. 5.0. s.o., sn-95 t-5 and an f-150 clutch. Driven daily and going strong.
1986 cougar.
lilsammywasapunkrocker@yahoo.com

trans cooler line leaking ?

Reply #4 –
And your screwdriver needs to shave.LOL.
'88 Sport--T-5,MGW shifter,Trick Flow R intake,Ed Curtis cam,Trick Flow heads,Scorpion rockers,75mm Accufab t-body,3G,mini starter,Taurus fan,BBK long tube headers,O/R H-Pipe, Flowamaster Super 44's, deep and deeper Cobra R wheels, Mass Air and 24's,8.8 with 3.73's,140 mph speedo,Mach 1 chin spoiler,SN-95 springs,CHE control arms,aluminum drive shaft and a lot more..

trans cooler line leaking ?

Reply #5 –
Quote from: vinnietbird;316283
And your screwdriver needs to shave.LOL.


:rollin:
[SIGPIC][/SIGPIC]
***** Project "EVOLUTION" 1987 Cougar LS  & 1985 Cougar Convertible *****
[/COLOR]
5.0 HO 306 roller block, machined GT-40P heads, Wiseco dished forged pistons, Eagle forged floating I-beam connecting rods, Lunati pushrods, ARP bolts, Scorpion aluminum 1.6 rockers, Comp Cams Magnum 266HR, Explorer intake, 65mm TB, MAF Conversion, 19# injectors, Ford Racing stainless P-headers, 2-1/2" cat-less exhaust w/ Flowtech Afterburner lers , SC AOD with 2800 BDR torque converter, 3.73 T-Lok rear, CHE rear control arms, full 2-1/2" frame w/1" jacking rails & seat supports, Rear disk brakes, Turbine wheels, All original interior w/ floor shift upgrade .......
Pretty much every panel on my 87 is new, rebuilt, or re constructed. :D
Join us on Facebook
http://www.facebook.com/home.php?sk=group_137541156293768&ap=1

trans cooler line leaking ?

Reply #6 –
Quote from: Dansbirds;316232
Its a 86 XR7 and I cant get the top cooler line at the radiator to stop leaking. It isnt leaking from the rad fitting but from the line at the nut.  Any suggestions will be greatly appreciated


The Ford P/N is E6VY-7D273-A for a pack of two. One for the trans end and one for the radiator. They are different sizes.

Slide something thin along two sides of the tubing to move the nylon tabs and pop it out.

trans cooler line leaking ?

Reply #7 –
There are two O rings inside the connector. It looks like a PITA to replace. But maybe it could be done.

trans cooler line leaking ?

Reply #8 –
Thanks guys, it is a PITA to remove. I cut a piece of plastic and used that to get it off.  I will see about shaving the screwdriver once I get the car back together, still trying to figure where I picked up all the metal shavings on that screwdriver
 

trans cooler line leaking ?

Reply #9 –
Just a update for future refrence. Bought the autozone piece and it was not correct. I believe they could get it but I needed to fix it now. There part # 800-608 is wrong, I think it should be 800-609. Anyway went to Ford (thanks for the p/n softtouch) they had it in stock and it is cured.