Skip to main content ↑ ↓
Topic: valve covers (Read 1327 times) previous topic - next topic

valve covers

dose anyone know how hard it is to put new seals on valve covers and what do i have to take off to do it
[SIGPIC][/SIGPIC]
88 5.0L aod with duel flowmaster and speedo mod
88 5.0L H.O with 5 speed R.I.P
87 3.8L no trans. geting h.o and 5speed (project never ending thunder) started it as of 8-14-10
96 bronco xl 5.0L 5 speed man4x4
:birdsmily:

valve covers

Reply #1 –
Pull the upper intake,remove the 6 bolts from each valve cover,remove the valve covers,clean the mating surfaces of the valve covers and the heads really good,purchase new rubber valve cover gaskets,place them on the heads,place the valve covers on top of the gaskets,bolts them down (it doesn't take much to torque them down),re-install the upper intake,done.
'88 Sport--T-5,MGW shifter,Trick Flow R intake,Ed Curtis cam,Trick Flow heads,Scorpion rockers,75mm Accufab t-body,3G,mini starter,Taurus fan,BBK long tube headers,O/R H-Pipe, Flowamaster Super 44's, deep and deeper Cobra R wheels, Mass Air and 24's,8.8 with 3.73's,140 mph speedo,Mach 1 chin spoiler,SN-95 springs,CHE control arms,aluminum drive shaft and a lot more..

valve covers

Reply #2 –
is their a patern to bolt down the valve covers
[SIGPIC][/SIGPIC]
88 5.0L aod with duel flowmaster and speedo mod
88 5.0L H.O with 5 speed R.I.P
87 3.8L no trans. geting h.o and 5speed (project never ending thunder) started it as of 8-14-10
96 bronco xl 5.0L 5 speed man4x4
:birdsmily:

valve covers

Reply #3 –
I'm sure there is.I just start from the middle and work my way out.Snug them,then tighten them.There's only 6 per side.
'88 Sport--T-5,MGW shifter,Trick Flow R intake,Ed Curtis cam,Trick Flow heads,Scorpion rockers,75mm Accufab t-body,3G,mini starter,Taurus fan,BBK long tube headers,O/R H-Pipe, Flowamaster Super 44's, deep and deeper Cobra R wheels, Mass Air and 24's,8.8 with 3.73's,140 mph speedo,Mach 1 chin spoiler,SN-95 springs,CHE control arms,aluminum drive shaft and a lot more..

valve covers

Reply #4 –
oops.. I went with cork..:toilet:
1988 Cougar LS 5.0 (currently parting out):cougarsmily:
1989 Mustang LX Notch 2.3 (Project):ford:

valve covers

Reply #5 –
The rubber ones are really nice,reuseable,and seal great with no sealer.
'88 Sport--T-5,MGW shifter,Trick Flow R intake,Ed Curtis cam,Trick Flow heads,Scorpion rockers,75mm Accufab t-body,3G,mini starter,Taurus fan,BBK long tube headers,O/R H-Pipe, Flowamaster Super 44's, deep and deeper Cobra R wheels, Mass Air and 24's,8.8 with 3.73's,140 mph speedo,Mach 1 chin spoiler,SN-95 springs,CHE control arms,aluminum drive shaft and a lot more..

valve covers

Reply #6 –
CORK SUCK
this is a simple job
best off throwing a thin bead of sealer on it to be safe
and watch wireing connectors and vacuum lines!!
RIP 1988 and 1990 Lincoln Mark VII LSC
I welcomed the dark side and currently am driving a 2000 Dodge Durango SLT plus, with a 5.9, Code named project "Night Runner"
Shes black on black, fully loaded, with headers, 180 tstat, e fan, straight exhaust into a cherry bomb vortex ler, full tune up, ported intake and T/B, MSD coil, and round aircleaner.
Mods to come: Fully rebuilt and heavily modded 46RE, and a richmond rachet locker.
my $300 beater ;)
R.I.P Kayleigh Raposa 12/18/90 - 2/24/07

valve covers

Reply #7 –
Meh I've used cork Felpros with no leaks for years :mullet:
88 Thunderbird LX: 306, Edelbrock Performer heads, Comp 266HR cam, Edelbrock Performer RPM intake, bunch of other stuff.

valve covers

Reply #8 –
all ive ever used is cork.

rubber is nice, but cork to me is the only way to go

valve covers

Reply #9 –
Is there any difference between Carb and EFI valve covers?
[SIGPIC][/SIGPIC]


http://www.cardomain.com/id/Carpimp1987
1987 T-Bird AEROBIRD-GT had many many mods but is now totaled and is the car that made me want to start customizing everything all over again.
1988 T-Bird 5.0 HO DD/Sleeper/next project car :birdsmily:
1988 Cougar XR7 5.0 HO Vortech Supercharged being bulit right now :cougarsmily:

valve covers

Reply #10 –
Yes,there's a difference in the covers,but the gaskets are the same.
'88 Sport--T-5,MGW shifter,Trick Flow R intake,Ed Curtis cam,Trick Flow heads,Scorpion rockers,75mm Accufab t-body,3G,mini starter,Taurus fan,BBK long tube headers,O/R H-Pipe, Flowamaster Super 44's, deep and deeper Cobra R wheels, Mass Air and 24's,8.8 with 3.73's,140 mph speedo,Mach 1 chin spoiler,SN-95 springs,CHE control arms,aluminum drive shaft and a lot more..
 

valve covers

Reply #11 –
Well.. I used the permatex gasket seal maker on both sides of the gasket. I guess time will tell.:D
1988 Cougar LS 5.0 (currently parting out):cougarsmily:
1989 Mustang LX Notch 2.3 (Project):ford: