1
Show Posts
This section allows you to view all Show Posts made by this member. Note that you can only see Show Posts made in areas you currently have access to.
Messages - ianb
2
T-Bird/Cougar Parts & Cars FOR SALE / 1988 TC with PIMP runs good..new clutch..$3000 obo..trade for bike
Approx 196k on it
Bad-
-Needs some body work to be mint..driver side needs it mostly
-comes with a spare driver side door/driver side fender (need to dig it out of friends basp00get)
-Needs ebrake cable on pass side
Good/mods
-Has a Pimp ver 1.3 with a AEM wideband
-Oil, boost, coolant Autometer gauges
-Put in new windshield about 2 years ago
-kirban adjustable fuel pressure regulator gauge
-volvo front mount intercooler with blow off valve and stinger piping kit
-put on non tc thunderbird grill but have stock tc header panel
-ranger radiator with universal 14" fan
-walbro 255 high pressure pump from JDS
-3" downpipe no cats and dynomax ultra flow lers
-Stinger 2.5 stainless tailpipes
-full hurst short throw shift with stops
-gillis manual boost controller
-17X8 Cobra r reps
-front pads, rotors, calipers, and lines replaced middle of last year
-95 Amp upgraded alternator
-75 lb injectors Delphis low impedance
-super coupe throttle body
-Slightly ported/bellmouther upper
-ford ranger valve cover gasket
-Maximum Motorsports caster camber plates
-Lowered approx 1 1/2 inches
-Comes with ported E6 (not installed)
-.48 T3 Turbo with inlet and oil drain (not installed..im lazy)
-some random spare parts
-Just did clutch/rear main seal
-Underneath does not have any rot
Im just not into it anymore and have some bills I wouldn't mind tackling. Located in 203 CT looking for around $3000 or possible trades for a cruiser style motorcycle
https://lh3.googleusercontent.com/-9ASCdrGosPU/VGt-GXlvaEI/AAAAAAAAVlo/YpDGLAAUljY/s640-Ic42/IMG_8606.JPG
https://lh3.googleusercontent.com/--f6tl9AgHNU/VGt-HWl_EUI/AAAAAAAAVlw/o7a6Gi8MD8c/s640-Ic42/IMG_8614.JPG
https://lh3.googleusercontent.com/-UyK1844v7pE/VSwTFYU10xI/AAAAAAAAb3Y/CQADm7htrvs/s720-Ic42/IMG_0003.JPG
https://lh3.googleusercontent.com/-hkjCnv60cA4/UzecYPGLZqI/AAAAAAAAN2c/nf0Dv5OcjNU/s640-Ic42/P1050085.JPG
https://lh3.googleusercontent.com/-f421ZbGsQrM/Uzy3sA_disI/AAAAAAAAONE/YGQqCb3KopU/s640-Ic42/IMAGE_492.jpg
https://lh3.googleusercontent.com/-8ESwkVe2ot8/VSG8VyUFpII/AAAAAAAAbnE/bQC3dpiu00c/s640-Ic42/IMG_2392.JPG
Any questions shoot me a PM or post in here..thanks everyone!
3
T-Bird/Cougar Parts & Cars FOR SALE / .48 t3 for sale in CT $250 obo
http://newhaven.craigslist.org/pts/5110908700.html
Looking for around $250 + shipping
4
T-Bird/Cougar Parts & Cars WANTED / Anyone with a 4 eye TC willing to swap for a 87-88 setup
5
T-Bird/Cougar Parts & Cars WANTED / Needed 88 tc throwout bearing retainer...
Quote from: V8Demon;447374
Napa has it. Check their website.
Maybe i'm blind but I couldn't see it...
http://www.napaonline.com/Catalog/Result.aspx/Ford-Thunderbird-1988/_/Ntk-Category/Ntt-Clutches%20Related%20Parts/N-599001%20101988%2050026%202026030%204026006%205999999
6
T-Bird/Cougar Parts & Cars WANTED / Needed 88 tc throwout bearing retainer...
V8 ones wont work FYI
Thanks!
7
Vendor/Seller Feedback / Kudos to Chuck W.
8
T-Bird/Cougar Parts & Cars FOR SALE / T3 ar60 for sale..off a merkur.. Located in CT
$300 plus shipping with the elbow
https://lh5.googleusercontent.com/-wLwjMY1C2to/VQ8ARiq2mCI/AAAAAAAAbc4/2bA2FGehhy4/w958-h719-no/IMG_2016.JPG
https://lh5.googleusercontent.com/-uLZaI1CHljw/VSrxV-rlNvI/AAAAAAAAb14/BpbUfYY27qE/w958-h719-no/IMG_2557.JPG
https://lh6.googleusercontent.com/-ztfd5ZZrApQ/VSrxWolYtPI/AAAAAAAAb2A/VwosdK4PwvY/w607-h809-no/IMG_2558.JPG
https://lh5.googleusercontent.com/-c4BuuyOZiyA/VSrxXW9-o3I/AAAAAAAAb2I/z3Mh0FgPI1k/w958-h719-no/IMG_2559.JPG
9
T-Bird/Cougar Parts & Cars FOR SALE / 88 TC part out
10
Vendor/Seller Feedback / Kudos to Chuck W.
11
Suspension/Steering / Jacking my 88 TC back up =( from cut springs to sn95s....Advice long thread
So I retract my last statement I did actually have my bump stop on my strut minus the dust boot. I also found 4 large spacers UNDER the bearing. So that explains my strut bottoming out so easily. So I added in a isolator on the top of the springs and I it looks like I gained a tiny more clearance. I drove it around briefly and it felt much better over bumps. I have to get a alignment tomorrow and give it a few weeks. I am pretty pumped to drive it.
-And the rears holy ..man I had to jack up the ass end lot to get the shocks to line up. I used old SN95 tokicos which I think came off a bullitt or Mach 1. But either way the isolators are in all around and I feel that they gave me a extra bit of height.
As you can see as a result of hitting the worst pot ever made and also not great spacing on the strut.
Here comes the scary part
Thank you Mr Tranny Jack...this is so much easier than doing it on the ground
Stock bump stop
Maximum Motorsports
New py stock shock in place with spring and isolator
I unforutnalty did not take many pics of the finished product as it was getting late and I needed to hustle. But I ran two of the bigger spacers under the bearing and then 1 large one followed by one thin one on the top.
I hope that somebody down the road can use all these pics for future reference!!!!
12
Suspension/Steering / Jacking my 88 TC back up =( from cut springs to sn95s....Advice long thread
13
Body/Appearance/Interior / Metal piece inside of headlights 87-88 Tbirds??
Quote from: BornInAFord;441464
Are you talking about the lightbulb itself, or the headlight housing?
I don't know much that can help with the stock headlight brightness, unfortunately. From the factory, they weren't as good as any of today's HID-equipped cars. After a few years of UV degradation, the polycarbonate lenses aren't helping either. You can help a bit by cleaning/restoring/sealing the lenses and by using brighter bulbs (along with using relays to minimize stress on the switch).
I wish updated, new housings were being produced that fit our cars...
Na its actual piece of the housing inside of the headlight not the bulb. And yeah I wish new housing were made night vision is crucial.
14
Suspension/Steering / Jacking my 88 TC back up =( from cut springs to sn95s....Advice long thread
Currently how it sits
I love the way it looks but hate the way it rides. I've debated on doing just the struts and seeing how much the ride improves...but from everything i've read cut springs will kill the struts prematurely and ride like .
However I never replaced this part when lowering it and like an idiot tossed it out lol
I know I know its very very stupid. So right now its just strut on caster/camber plate. I also didnt set the shims corrector on the plates as well. I did it a very very dumb way. I'm guessing this accelerated the death of my struts.
-Needless to say I have been doing my research and have gotten install instructions from Maximum Motorsports website.
I just picked up a set of 1995 stock V8 Mustang springs just now. I also have some stock SN95 Monro sensatracs for the front and rear. My plan was to swap in the stock height SN95 springs and stock shocks and struts. I am honestly disgusted by the wheel gap on my stock setup and it saddens me thinking about it lol. Seen here
So as i'm typing this i'm realizing more and more wondering if should attempt to install the struts the right way before swapping springs maybe? The stock height SN95's came with the thicker isolators seen here..I was debating on putting these on my cut springs to give a slight increase in height..
https://lh3.googleusercontent.com/-6C__u3ABVbs/VIiVldV2XhI/AAAAAAAAVv8/jfvsSwbWkDM/w407-h542-no/IMG_9649.JPG
I apologize as im all over the place and in case you cant tell I really don't like a large amount of wheel gap. I feel that some of my handling issue's are a issue of extremely beat from struts. Its possible the struts were killed early because of not being install properly. And the fact that I cut off a coil isnt helping either. Should I bother to continue messing with my cut springs (+ upper isolators this time) or just slap in the stock height SN95's and be done with it?
15